2013 JDsleds.com Raffle Sled OFFICIAL TOPIC

Post by **WinnipegStPaul9** » Wed Apr 25, 2012 9:22 pm

I believe the windshield has been taken care of .

DA

JDT · Post by **JDT** » Wed Apr 25, 2012 9:37 pm

Ed, Brock and Matt.
I would like to donate cash towards the build to be used for needed parts.
Please PM me with how and where to send my contibution.
Thank you.

cledussnow77 · Post by **cledussnow77** » Wed Apr 25, 2012 9:39 pm

Thanks Matt for getting the list posted

, now we just need everyone to do what they can to make this successful.

Sprailfire340 · Post by **Sprailfire340** » Thu Apr 26, 2012 10:26 am

Pretty sure I have chaincase & drive bearings on hand. I'll send them your way.

nick80lf · Post by **nick80lf** » Thu Apr 26, 2012 4:55 pm

I'll get the tail light and fuel pump

Horicon Joe · Post by **Horicon Joe** » Thu Apr 26, 2012 5:35 pm

Matt you can please give them the ski isolators and wear blocks for the suspension next time there is a shipment going out.

Thanks guys!

Joe

cledussnow77 · Post by **cledussnow77** » Thu Apr 26, 2012 7:55 pm

Thanks guy's for the donations so far

, still have a big list. Any monetary donations should be sent to Matt and all the parts should be sent to Brock's place. Can't wait to get some more work done on this sled next weekend.

400brian · Post by **400brian** » Thu Apr 26, 2012 7:57 pm

Horicon Joe wrote:Matt you can please give them the ski isolators and wear blocks for the suspension next time there is a shipment going out.

Thanks guys!

Joe

If we are talking about a stock '78 ( non Cross Country ) suspension, it doesn't use the wear blocks ( M64482 ).

nick80lf · Post by **nick80lf** » Thu Apr 26, 2012 8:14 pm

deleted

DeereKid9 · Post by **DeereKid9** » Thu Apr 26, 2012 8:55 pm

It's not much, but consider the wear bars and Hyfax taken care of.

Carbide OK? That is what I would want.

Bob

skoalmint · Post by **skoalmint** » Thu Apr 26, 2012 9:29 pm

WOW Guys !!!!!!! That was quick ,good to see people chipping in already .Thanks ALOT!! I guess WE better get on it.Sounds like parts are gonna be waiting on us ,instead of us waiting on them.Thanks again Brock

Post by **WinnipegStPaul9** » Fri Apr 27, 2012 6:29 am

I know you all are anxious to get started but allow me to give you one piece of advice. Have ALL parts present and accounted for BEFORE the build. On our previous build day, when we all walked in the door on that Saturday morning all parts were laid out yet we still had to wait while some parts were refurbished and even painted. Thank God we had the facility (PJ's) to do that. That is all for now...................dismissed.

DA

cledussnow77 · Post by **cledussnow77** » Mon May 07, 2012 1:22 pm

Another awsome time at Brock's place

,Dustin got the suspension tore apart, Nick blasted them, Brock got them in primer. I got the chassis stripped down and power washed and the wiring block taken apart, cleaned and put back together. Brock and I got the dash and side vents cleaned, scuffed and primed. Dustin got the hoodhinge mount welded and fixed and primed. Nick got the drivers off and got the shaft blasted and primed. Brock also got the exhaust manifold and pipe sanded, primed and painted. Brock's wife Tammy had us hooked up with a good lunch and an awsome supper with an amazing desert

. Thanks Tammy, AWSOME job, we don't care what Brock says when your not around

.