NEEDED ASAP

400brian · Post by **400brian** » Fri Feb 07, 2014 5:27 am

I need a set of NOS secondary clutch buttons for a Comet . AM52995 or AM53738

Leaving for St Germain on the 13th, Wife's sled needs a set. I thought I had some, but it turns out they are Salsbury.

Can anyone mail me a set today?

RLFollman · Post by **RLFollman** » Sun Feb 23, 2014 2:44 pm

Here's the Comet cross-reference information and sources for the AM52995 / AM53738 buttons. They're everywhere!

Comet Cross Reference:
http://www.jdsleds.com/tech/comet/deeretocomet.pdf

Sources:
http://www.mfgsupply.com/204332a.html

http://www.amazon.com/Comet-Nylon-Butto ... B005DUN7KW

http://beltpalace.com/comet204332a.html

ebay search "204332a"
http://www.ebay.com/sch/i.html?_trksid= ... &_from=R40

http://www.walmart.com/ip/Comet-204332A ... 3/26964736

http://www.newegg.com/Product/Product.a ... 02V0SN3646

Post by **WinnipegStPaul9** » Sun Feb 23, 2014 4:43 pm

WALMART!!! I about died laughing but it is true.

DA

Post by **Matt** » Sun Feb 23, 2014 6:36 pm

Wow, I did not know these were available. I'll add them to my store.

Post by **WinnipegStPaul9** » Sun Feb 23, 2014 8:10 pm

Matt, I'd bet there are some that are not as good as others. Please try to stock the best ones, they'd be worth the cost. Thanks,

DA

JDT · Post by **JDT** » Sun Feb 23, 2014 8:49 pm

If you can't trust Walmart than who can you trust?

Post by **Matt** » Sun Feb 23, 2014 10:31 pm

Don, supposedly the ones I'm ordering are genuine Comet and came from CPC. I'll see for sure when they get here.

Post by **WinnipegStPaul9** » Mon Feb 24, 2014 7:51 am

Steven · Post by **Steven** » Mon Feb 24, 2014 9:15 am

I'd like to know some opinions on using glue for these. Yes/no, what type? I changed the shoes on a 76 liquifire this weekend and those buttons sit pretty deep and have a nice seat to sit in so i didnt use anything. I've got 2 different sets coming this week for a salsbury and a comet90d. These comet ones are short and stubby. I'll pull them back out on the liqui and use glue on all three clutches if need be.

Sent from my iPhone using Tapatalk

JDT · Post by **JDT** » Mon Feb 24, 2014 10:01 am

Never used any glue on installing these.

The helix holds them in and the stem should be snug friction fit.

Steven · Post by **Steven** » Tue Feb 25, 2014 11:05 am

Ok thanks for the reply JDT. The reason I asked was in the service manual for the 76 LF says to use a 2 part epoxy or cement, but in the 00 series book it says nothing about it. Perhaps the intention was to make the person drill out the old stem and in doing so you'd have to take it apart and inspect the rest of the clutch?

Sent from my iPhone using Tapatalk

skoalmint · Post by **skoalmint** » Tue Feb 25, 2014 11:28 pm

I think Deere was worried about when the clutch back shifted that poss a ramp slide could pop out. Thats why the epoxy was recomended. Brock

JDT · Post by **JDT** » Wed Mar 05, 2014 2:25 pm

My concern would be the glue reacting with the plastic and making it brittle.

NEEDED ASAP

NEEDED ASAP

Re: NEEDED ASAP - AM52995 / AM53738 buttons

Re: NEEDED ASAP

Re: NEEDED ASAP

Re: NEEDED ASAP

Re: NEEDED ASAP

Re: NEEDED ASAP

Re: NEEDED ASAP

Re: NEEDED ASAP

Re: NEEDED ASAP

Re: NEEDED ASAP

Re: NEEDED ASAP

Re: NEEDED ASAP