Speedo thingy!!
-
Popcorn popper
- Posts: 225
- Joined: Tue Dec 29, 2020 6:21 pm
- Real Name: Steve
Speedo thingy!!
Does anyone know if that little cable thingy that goes from right angle drive to axle is available or is it a scavenger part? Looked at two already both twisted off.
-
Platinum_2
- Posts: 66
- Joined: Sun Nov 22, 2020 7:30 pm
- Real Name: Gary
Re: Speedo thingy!!
If you're asking about the square speedo key/shaft, they are widely available. New breed has them.
1981 Liquifire
1980 Sportfire
1980 Sportfire
Re: Speedo thingy!!
Been using 3280017 Polaris part because we have them on the shelf at the dealership.
1973 John Deere 400-Fall 08-Ongoing project
1980 John Deere Trailfire 340 (RAT)- Spring 09- Daily rider
1982 John Deere Trailfire 340 - Spring 12- Daily rider
1980 John Deere Liquifire 440- Fall 12
1976 Arctic Cat Jag 2000 F/A Fall 10
1976 Arctic Cat Jag 3000F/A- Summer 10-Daily Rider
1980 Arctic Cat Jag 3000F/A-Summer 10
1988 & 1991 Polaris Indy 650s
"If You Don't Know Where To Start, Go Back To The Beginning"
1980 John Deere Trailfire 340 (RAT)- Spring 09- Daily rider
1982 John Deere Trailfire 340 - Spring 12- Daily rider
1980 John Deere Liquifire 440- Fall 12
1976 Arctic Cat Jag 2000 F/A Fall 10
1976 Arctic Cat Jag 3000F/A- Summer 10-Daily Rider
1980 Arctic Cat Jag 3000F/A-Summer 10
1988 & 1991 Polaris Indy 650s
"If You Don't Know Where To Start, Go Back To The Beginning"
-
Popcorn popper
- Posts: 225
- Joined: Tue Dec 29, 2020 6:21 pm
- Real Name: Steve
Re: Speedo thingy!!
-
Popcorn popper
- Posts: 225
- Joined: Tue Dec 29, 2020 6:21 pm
- Real Name: Steve
Re: Speedo thingy!!
Also the little screw for lid above carb. Cant find anywhere around here.
-
400brian
- Posts: 5626
- Joined: Wed Jul 20, 2005 12:00 am
- Real Name: James T. Kirk
- Location: South Central Wisconsin
Re: Speedo thingy!!
The knurled thumb screw is still available from Deere. Part number M63672. I retain them with a round piece of aluminum sheet that I cut a small hole in, then snip a notch into the side of the hole so I can thread the thumbscrew into it. Put the screw into the panel, thread the retainer on it, bend the notch down, and it will probably stay.
The speedo drive key is made of speedo cable. So it is a twisted cable essentially. So, you have 2 options to remove it: if there is some of it sticking out, you may be able to grab individual wires and pull them out. This probably is a waste of time, but hey take a shot. Drilling it out is problematic as it is in a square hole. Even if you can successfully drill it out, you may have messed up the square drive. The other option is to replace the entire drive bushing from the driveshaft. You can drill the old one out and replace the whole thing. I'm thinking the hole in the driveshaft is 1/4" or something like that. You Loctite the new one in and you are all set. The guys hoarding the NOS parts have these, as they were included in Speedo installation kits. Some of the guys have been using those kits just for the hardware.
The speedo drive key is made of speedo cable. So it is a twisted cable essentially. So, you have 2 options to remove it: if there is some of it sticking out, you may be able to grab individual wires and pull them out. This probably is a waste of time, but hey take a shot. Drilling it out is problematic as it is in a square hole. Even if you can successfully drill it out, you may have messed up the square drive. The other option is to replace the entire drive bushing from the driveshaft. You can drill the old one out and replace the whole thing. I'm thinking the hole in the driveshaft is 1/4" or something like that. You Loctite the new one in and you are all set. The guys hoarding the NOS parts have these, as they were included in Speedo installation kits. Some of the guys have been using those kits just for the hardware.
'09 Vintage Challenge Survivor, and I wasn't late for supper!
'10, '11, '12, '13,'14,'15,'16,'17, '18, 19, 20, 21, 22 Vintage Challenge Survivor !
72 400 restored, Father bought new in '71
73 X8 restored
'74 340 green machine
'74 X8 9 time VC finisher
'78 Spitfire in progress
2 '75 340S 1 running, one on deck
'78 LF 440 future CC clone
'73 Skiroule RTX 440, 500 mi.
-
Popcorn popper
- Posts: 225
- Joined: Tue Dec 29, 2020 6:21 pm
- Real Name: Steve
Re: Speedo thingy!!
Wow thanks Brian. John Deere has some of the weirdest parts available lol. I bought brake band there also from info received here. Im very surprised. Anyway thanks again. Its been a interesting project.